rotate-watches-sol-part-3

Rotate Watches SOL Part 3

Rotate Watches SOL closeup

When we left off in Part 2 last week month, it was unknown whether I’d seriously damaged the Rotate Watches “make it yourself” movement. Good news: nope, it’s fine. Bad news: I’m still SOL. Minimal progress and another impasse! Nonetheless, this all took gobs of time and effort. Gather round to hear of my foibles. If you’re not careful, you may learn something before it’s done . . .

Previously, I was worried sick about the set/wind lever system. It didn’t shift between these two functions with the stem in/out. I’d neglected getting back to customer service with more details. This let me hope that I hadn’t irreparably bunged it all up. I finally sent a short demonstration video off to our heroine and savior Jen, the tireless and cheery one-woman support team.

fussbudget, checking function before told to, I’d have tightened that screw in the next couple steps anyway. So this was much ado about nothing.

I still had to cut the replacement stem to length. It later realized that the original stem was likely never cut too short and was a similar victim of my fretting. I refuse to check and find out. Anyway, the first step is loosening that screw I’d just tightened. You may note that the process has lots of repetition. You may note that the process has lots of repetition. Sisyphus levels, almost.

Flip the movement over to loosen that screw to pull the winding stem. Removing the stem while the movement is still upside down can lead to the pinion gear surrounding the stem falling out. Yes, the one I’ve already lost and replaced once already. That one. This immediately happened again, which is how I learned how I lost the first one. I got even more practice reinstalling that gear.

Rotate Watches SOL RTFM
I don’t read so good

Did I mention that the directions warn against overtightening that stem-securing screw too? Somehow that detaches a piece too. Because it holds on . . . hold on, let’s get that stock image again. The part the red arrow points to, Set Lever Ebauches #443. That screw is the mounting and the pivot. Yikes. Yup. Rotate Watches SOL again.

Image courtesy of TZtoolshop.com

That fell out. Getting it back in was a trick. It must be slid under that piece with the green arrow, which happens to be acting as a spring. Since the little peg goes into a slot in a spring, the loose piece becomes ammunition in a  tiny catapult. It wants to shoot the piece into the beyond, much like spring bars do under their own power.

I thought I saw the launched piece land between two floorboards. I really, really didn’t want to go crawling back to Rotate for a third round of free spare parts because I’d screwed up yet again. The shame would be unbearable. I must hide this embarrassment  by finding the piece!

Thus I created a wee archeological dig using another set of tweezers. I excavated ancient crud from the crevice and carefully sifted through it. Old staples, plastic clothing tag sprues, broom bristle fragments, fingernail clippings were all found. But not the little squiggly metal part. Was it magnetic? Dragging magnets yielded nothing. Would a flashlight help, an UV one?

Bad lighting here as the photographer was a bit frazzled

Oops, I found it by the table leg edge. Not so Rotate Watches SOL now, eh Mr. Bond? Back to installation . . .

So after slipping it under one piece and pushing against a spring, just line up the threaded hole over the screw. The screw that tightens from the other side, from the bottom. This took many, many attempts. But I finally emerged victorious.

Rotate Watches SOL again Back together. Stem still too long.

We’re still at the stem trimming step? I was shy about trimming too much, again. But I’m not doing all this just to end up with a big gap between the case and crown. More repetition, this became like Zeno’s paradox. Clip the stem, insert it, and keep getting closer but never fully there.

Finally it reached the point where cutting a thread pitch risked being too much, but I still minded the gap. I thought I had some sandpaper around last time, but it was nowhere to be found. So I had to use a nail file like a total sissy. It turns out the steel stem end files down nowhere as fast as a fingernail.

Alas, it’s good enough. Open the krazy glue, dip the stem end and thread that crown on for the last time.  Good night, cure overnight.

small tab is small

All this time the movement had just been friction fit into the case. Two little metal tabs need to be screwed in to lock it in place and prevent rotation or shifting. Of course these are tiny little pieces. By this point, I was done with the gloves, regardless of what the directions said.

Yet again, the process was supposed to be one of finesse but really was an infinite number of hapless attempts hoping for the stars to align. Use the tweezer to drop the tab in place. Repeat with the screw, hoping to somehow get it through the loose tab and the threaded hole, then tighten. The final hole in mini-golf, putting through the windmill blades, is a snap in comparison.

The supplied screw driver is truly not up for the job. It doesn’t fit the slot in width or length. Even when magnetized with the help of a refrigerator magnet, the screw would dangle off at wobbly angles instead of being firmly pointable.

The taming of the screw

I quickly lost one screw, and just proceeded with the other one. Eventually I realized that the wound movement’s balance spring had stopped. Yes, the lost screw was jamming it. This was a tense moment, but a tweezer extraction mission led to returned operation. When the screw disappeared again, it was much easier to find it in the same place the second time.

See also the main photo at top!

Rotate had initially offered to replace the “dull” screwdriver. I declined. This was a mistake. However, as these screws are larger than one securing the stem I revisited that cheap Harbor Freight precision screwdriver kit. It worked much better here. I got the hole in one on the first shot!

One down, one out. Why is there a shadow under tab? Come back next week!

Then the second screw shot off somewhere. A repeat search operation couldn’t locate it. So I begged poor Jen at Rotate for help one last time. I tried to coax them to charge me for the amount of nuisance and and profit loss I’m causing. They were having none of it.

Bonus: Vaer sent out a video about what their American assembly entails. Despite being a Vaer fan, I’d have previously scoffed at this. Now, not so much, and I’m not even regulating or testing pressure ratings.

So . . . not done yet. Stay tuned for another exciting chapter of Rotate Watches SOL, or how I learned to stop worrying and screw it up again.

Related Posts

Lascia un commento

Il tuo indirizzo email non sarà pubblicato. I campi obbligatori sono contrassegnati *